您好,欢迎您来访济南天锐升降机械有限公司! 公司主营:液压升降机、液压登车桥、液压升降平台、液压升降货梯等。

济南天锐升降机械有限公司

液压升降平台
丰富的升降机设备生产经验
为您提供用心的升降机全套解决方案
分类导航CLASSIFIED NAVIGATION
联系天锐机械 / Contact us
联系天锐机械

济南天锐升降机械有限公司

客户统一咨询热线

188-5411-2626

联系电话:0531-84250097

公司地址:山东省济南市济阳区济阳街道工业园15-4号

当前位置:  >  新闻中心

济南液压升降机导轨架如何安装?

文章来源:www.trsjjx.com   发布时间:2014-10-16 10:02:32   浏览次数:

返回:新闻动态

济南液压升降机导轨架是用作支撑和固定导轨用的构件,被安装在井道壁或横梁上,它固定了导轨的空间位置,并承受来自导轨的各种动作,在升降机导轨架安装时应注意一下安装事项。
  
1、井壁有预埋铁时,安装前要先清除其表面混凝土,根据导轨基准线及辅助基准线确定导轨支架的位置,将标准节两端管子接头处及齿条销子处擦干净,并加少量润滑脂,在地上将4节标准节连成一组,然后吊上导轨架对准下面标准节主管和齿条上的销孔,用螺栓坚固;随着导轨架的不断提,应同时安装附墙架,并检查导轨架安装垂直度,允许偏差100m小于90mm。
When there is embedded iron wall, remove it before installing the first surface of the concrete, determined according to the reference line and auxiliary reference guide line position rail brackets, standard section will clean both ends of the tube and rack pins at joints, and add a small amount of grease on the ground will be four standard sections together into one group, and then hanging on the rail frame alignment following standard section supervisor and pin holes on the rack, with the bolt firm; with the mention frame rails should be installed attached wall bracket and check rail rack installation verticality tolerance 100m less than 90mm.  
2、将吊笼开至下限位所允许到达的最低位置,放下手(电)动起重机的钢丝绳和吊具,在地面挂好一个标准节,缓缓摇动卷筒手柄(或启动电葫芦),将该标准节从地面护栏外提升至吊笼顶部并放好,操作人员带好标准节所需的联接螺拴、力矩扳手等工具,然后在笼顶操作升降机使吊笼上升。
The cage open to the lower limit allowed to reach the lowest position, put down your hand (electric) crane wire rope and spreader, on the ground and hung a standard section, slowly shaking reel handle (or start electric hoist), the standard lifting from the ground outside the fence section to the top of the cage and put away, the operator with a good standard section required connection bolts, torque wrenches and other tools, and then lift the cage top operation makes cage rise.
3、在装置根底结构时,首先应对装置根底结构的基面部位进行抄平处置,在导轨架的加节升高和装置附墙装置的过程中,应运用经纬仪沿导轨架的两个方向对其笔直度进行观测,经过附墙撑杆对导轨架进行恰当调整,使导轨架笔直度符合要求。
When the device structure of the foundation, the base surface portion of the first response to the foundation structure of the apparatus for copy flat disposal section of the rail frame in the elevated plus and the device attached to the wall of the process apparatus, it should be used in both directions along the guide rail rack straight theodolite degrees were observed after strut on rails attached to the wall bracket for proper adjustment, so that the degree of compliance with the requirements straight frame rails.
4、固定导轨用的压道板、紧固螺栓一定要和导轨配套使用。不允许采用焊接的方法或直接用螺栓固定(不用压道板)的方法将导轨固定在导轨架上,冬季不宜用混凝土灌筑导轨支架的方法安装导轨支架。在砖结构井壁剔凿导轨支架孔洞时,要注意不可破坏墙体。
Fixed rail track with the pressure plate, and rail fastening bolts must be supporting the use. The method does not allow the use of welding or bolted directly (without pressing channel plate)method will guide rails fixed shelves, winter should not install the rail bracket rail bracket with concrete pouring methods. When the brick wall tick chisel rail bracket holes, Be careful not to damage the wall.

 

济南液压升降机http://www.trsjjx.com/