您好,欢迎您来访济南天锐升降机械有限公司! 公司主营:液压升降机、液压登车桥、液压升降平台、液压升降货梯等。

济南天锐升降机械有限公司

液压升降平台
丰富的升降机设备生产经验
为您提供用心的升降机全套解决方案
分类导航CLASSIFIED NAVIGATION
联系天锐机械 / Contact us
联系天锐机械

济南天锐升降机械有限公司

客户统一咨询热线

188-5411-2626

联系电话:0531-84250097

公司地址:山东省济南市济阳区济阳街道工业园15-4号

当前位置:  >  新闻中心

导致济南液压升降机升温过高的因素分析

文章来源:www.trsjjx.com   发布时间:2014-6-10 18:04:53   浏览次数:

返回:新闻动态

液压升降机出现的以上情况,解决办法很简单,就是减小输入转速,检查下压盖的嵌入配合是不是太紧,检查液压升降机是不是缺油,检查各个蜗杆、涡轮和嵌套部位是不是需要润滑、保养了,只要勤检查勤保养以上这些导致因素有没有发生,发生了做到及时保养维护,油温升高的问题很快就可以排除掉。 
    Hydraulic lifts appear above situation, the solution is very simple, is to reduce the input speed, check the embedded with the gland is not too tight, check the hydraulic lift is not in oil, checking each worm, turbine and nesting sites are not needed lubrication, maintenance, and inspection as long as the ground handling and maintenance of these factors have led to the occurrence, timely maintenance, the problem of temperature rise occurred soon be excluded.                                 

    液压升降机使用得当的话,它的用途将非常广泛,作用也非常大。如果使用不当,或发生故障不能及时正确解决,也会大大缩短液压升降机的使用寿命,尤其是一些简单的很容易就能规避的问题。如作业中,液压升降机经常出现的温升过高和卡死的现象。下面金鼎集团技术小编就这个问题给大家介绍一些解决方法,希望能帮到需要的朋友。
    Hydraulic lifts used properly, then it will be very widespread use, the role is also very large. If used improperly, or failure can not be properly resolved, will greatly shorten the life of the hydraulic lifts, especially some simple problems can easily be circumvented. Such as operations, hydraulic lifts and a rise in temperature often appear stuck phenomenon. Here Jinding Group Technical Xiao Bian on this issue to give you some solutions, I hope to help a friend in need.

    经常发生温升过高的液压升降机多出现在导轨式液压升降机上面,因为导轨升降机要求的正常工作状态最高温度不得超过45摄氏度,如果出现高温,要立即停机检查。出现这种情况多是因为超负荷载重引起的。有时液压升降机的蜗杆和涡轮端盖压入得太紧也会出现高温情况,另外,涡轮导轨升降机输入转速时,坐高转速不能超1000min/s,如果输入的转速过高也会导致高温或卡死现象。
    Excessive temperature rise occurs frequently in multiple hydraulic lifts hydraulic lifts above the rail, because the normal working state rail lift maximum temperature should not exceed 45 degrees Celsius required, if there is a high temperature, they should immediately stop checking. This situation occurs because the overload caused by the load. Sometimes the worm and turbine hydraulic lift cap pushed too tightly will appear high temperatures, in addition, the turbine input speed rail lifts, sitting high speed can not exceed 1000min / s, if the input speed is too high will lead to high or card dead phenomenon.

 

济南液压升降机http://www.trsjjx.com/

 

查看更多液压升降机专业知识